4T-6694, 4T6694 Bolt On Segment for Caterpillar Front End Loader, CAT Bolt-on Cutting Edge Segment, Segment Edge Protection 25mm, BOLT ON LOADER SEGMENT, Caterpillar LOADER END BIT, 943 953 953B 953C 963 963B Loader End Edges, Replaceable Bolt On Cutting Edge and End Bit, Replacement CAT style Wheel Loader Edge, Double beveled reversible DBF bucket blade, CAT Wear Spare Parts China Supplier
4T-6694, 4T6694 Bolt On Segment for Caterpillar Front End Loader, Replacement Aftermarket OEM Parts 4T-6694, 4T6694 Bucket Cutting Edge Suitable for Loader, Backhoe, Buy Blade & End Bit CAT genuine, new parts with delivery, aftermarket, replacement and not original Caterpillar .
4T-6694 CTR BLADE SEGMENT 963 953 951 950 941 93
WEIGHT
12kg
DIMENSION
25
PROFILE
two
WIDTH
280
LENGTH
225
COMPATIBLE MODELS FOR PART NUMBER 4T-6694
INTEGRATED TOOLCARRIER
IT28F IT18F IT24F IT28G
WHEEL-TYPE LOADER
916 918F 924F 924G 924GZ 924H 924HZ 926 926E 928G 928HZ 930G 930H 930R 930T 936 936E 936F 938F 938H G916 G926
TRACK-TYPE LOADER
943 953 953B 953C 963 963B 963C 963D 963K
Replacement Cutting Edges
We stock and supply high wear cutting edges for the following types of machinery:
Loaders
Scrapers
Dozers
Excavators
Tractors
Skid Steers
& More..
We stock common edges for OEM manufacturers including:
CAT
Komatsu
Volvo
Deere
Case
Bobcat
Hyundai
& More..
Some of our common stock edges include:
Grader Blades
Cleanup Edges
Half Arrow
Router Bits
Hot Cupped End Bits
End Bits
& More…
We stock and are able to build for any specific bucket manufacturer: Accurate, Craig, Weldco Beales, CWS, AMI, HNL, Lemac, Daequip, and any others!
System Operation Description:Switch circuits may have problems such as faulty wiring, faulty switches, or faulty connectors. Use the following diagnostic procedures in order to diagnose problems with these switch circuits and repair these switch circuits:
Engine ECM reset switch. 4T-6691, 4T6691 Bolt-on Center Segment Edge
Start aid manual override switch
Start/Run/Stop switchNote: The engine ECM reset switch is installed by the customer.These switches are normally open or normally closed.
Illustration 1 g01366881 4T3015 Caterpillar Bolt-on Segment
Typical switch inputs and wiringTest Step 1. Check the Electrical Connectors and the Wiring
Remove the electrical power from the Electronic Control Module (ECM).
Illustration 2 g02164341
Location of the connectors that are for the switch circuits (typical left side engine view) (1) J1/P1 ECM connectors
Thoroughly inspect connectors (1) and the engine interface connectors. Thoroughly inspect the connections for the suspect switch. Refer to Troubleshooting, “Electrical Connectors – Inspect”. 4T3015 4T-3015 CAT 980 973 Loader End Cutting Edge
Terminal locations at the J1/P1 ECM connectors that are for the switch circuits (P1-22) Start aid manual override switch (P1-40) Start/Run/Stop switch (P1-41) Engine ECM reset switch 4T-6691, 4T6691 Bolt-on Center Segment Edge
Terminals at the engine interface connector that are for the switch circuits (Terminal 9) Start aid manual override switch (Terminal 16) Start/Run/Stop switch
Perform a 45 N (10 lb) pull test on each of the wires in the circuit for the suspect switch.
Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to Troubleshooting, “Electrical Connectors – Inspect” for the correct torque values. 4T-6692, 4T6692 Track Loader Bolt-on Center Blade
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM.Expected Result:All connectors, pins, and sockets are coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK – The wiring and connectors appear to be OK. Proceed to Test Step 2. 4T6692 Track Loader Double Bevel Reversible Segment
Not OK – There is a problem with the wiring and/or a connector.Repair: Repair the wiring and/or the connector. Replace parts, if necessary.
